PDM25 V2
The PDM25 V2 is the newest PDM (Power Distribution Module) from Hardwire Electronics, a natural update to the outgoing PDM25 V1. With new features such as High/Low side outputs, 9 Axis IMU, improved CAN bus and more.
A PDM is a device used to replace conventional relays and fuses in a vehicle electrical system. The Hardwire Electronics PDM25 takes inputs from physical switches, analogue voltages, or the CAN bus, and provides power to different electronic devices such as radiator fans, fuel pumps and head lights. The current being drawn from each connected device is continuously monitored. If the measured current is too high due to a fault, the PDM switches off the respective output to prevent further damage to the wiring loom or the connected device. The PDM can then retry the output to see if the fault has cleared.
Product Details
Included
- PDM25
- 4x DT/AT Connectors + Contacts + Wedgelocks
- 1x M8 Ring Terminal
- 1x Ring Terminal Cover
- USB Flash Drive with Pro PDM Configurator Software and Instruction preloaded
- 2m USB Cable
- Printed A4 instruction manual
- 2x Hardwire Electronics Stickers
Technical Specification
General
Size
200 x 160 x 54 mm
Weight
690g
Operating Temperature
-55 – 90C [ -67 – 194 °F ]
Construction
Glass Fibre reinforced plastic
IP Rating
IP67 Water and Dust Ingress Protection
Connectors
4x DT/AT
Inputs
Type
16 analogue inputs which can also serve as digital inputs.
Measurement Range
Each input can measure voltages between 0-28V, independent of the battery voltage.
Measurement resolution
12-bit or 0.01V
Frequency Measurement
Automatic frequency measurement up to 300Hz
Protection
Fully protected for input voltages between -24V to 40V.
Pull Up/Down Resistors
Each input has a permanent 200K Pull-up and 40K Pull-down resistor
Added Features
Configure as active high or low. Configurable Hysteresis voltage. Latching or momentary operation.
Outputs
Type
4 high/low side outputs 80A peak, 20A continuous (Pin-limited to 13A @125degC), with reverse current protection.
21 high side outputs 80A peak, 20A continuous (Pin-limited to 13A @125degC)
Combined
120A combined output maximum current
Output current control steps
100mA
Protection
Each output is overcurrent, overtemperature, load dump and reverse polarity protected.
Soft Start
PWM soft start can be enabled on outputs to limit inrush current.
PWM
Each output can be Pulse Width Modulated based on a user defined variable. This can limit the speed of radiator fans, fuel pumps, and dim lights.
1000Hz maximum PWM frequency
Added Features
Outputs can be configured to stay on for a specified time after the input is removed, useful for thermo-fans.
Outputs can be retried multiple times after an over-current event is detected.
CAN Bus
Interface
1x CAN2.0A/B ports
Bus Speed
50, 100, 125, 250, 500, 1000 kbps
Termination Resistor
Both CAN bus ports have software selectable CAN termination resistors.
Input Stream
100x inputs, fully customisable variable parsing with bit masking, math functions, and compound CAN message filtering
Output Stream
100x Outputs, Fully customisable CAN frame construction with math functions
CAN Keypad
Support for Blink Marine, Grayhill, Motec, Haltech and Marlin CAN keypads.
Up to 4x keypads can be used at once.
Logging
Storage
128Mb of onboard flash storage for logging PDM data
Speed
1Hz to 50Hz
Viewing
Data can be downloaded and graphed via the Hardwire Electronics PDM configurator software or exported as a .CSV file and graphed in external software
Functions
Output Functions
Each Output can be switched with a user defined function.
Logical operators
AND, OR, NOR, XOR, NAND, NOR, >, >=, <, <=, Equal, Not Equal.
Maths Channels
Fully customisable Maths Functions
Mathematical Operators
Mathematical Operators - Addition, Subtraction, Multiplication, Division, Modulus, Choose, Min, Max, Sin, Cos, Tan, Floor, Ceil, Abs, Asin, Acos, Ln, Log, Pow, Sqrt
Binary Operators
Binary Operators - AND, OR, XOR, Left Shift, Right Shift
Counters
Configurable counters which increment, decrement, and reset based on user defined conditions
IMU
Rotation
3-axis rotational position measurement 0.1° resolution
Gyroscope
2000°/s 3-axis measurement
Accelerometer
-8g to 8g 3-axis measurement
PCB temperature
PCB temperature measurement.
RTC
Real Time Clock with battery backup for 30 days. Used to store the correct time and date for data logs.
USB
Type
USB 2.0 compliant with Mini-B
Driver
Integrated driver with Windows 10
PC App
Name
Hardwire Electronics PDM configurator software.
Compatibility
Windows 10/11 machines
Connectivity
Easy connection to the PDM with USB and windows integrated drivers. No unreliable USB-serial converter needed.